5 comments about Paslode Cordless IMCT Framing Nailer #900420.

1. So far this nailer has worked out great.
   I'ver never used a framing nailer before, so I have nothing to compare it to. Im currently framing some new partition walls in my basement and I plan on adding some additonal decking outside.
   The only thing feature that hasn't lived up to its specs is the amount of nails that it will drive on one fuel cell. It seems like it has only driven a little more than half the amount stated. However, I'm not disappointed because the fuel cells are inexpensive enough.
   I highly recommend it to any noncontractor that has a relatively light use for a framiung nailer. The cost to buy it makes more sense than renting a nailer and a compressor for more than a few days. Especially if you may have a future use for it.



2. Just finished a shed project with this nailer... I wished I had bought it earlier! In a previous shed project, I've used a power actuated hammer (the one that fires the .22 blanks) to put hardened (expensive) nails into concrete block (the wall along the side of the shed is a 6' concrete block wall to which I attached the shed). On this project, I was able to use the Paslode nailer to do the same job much more quickly and I used the common framing nails (which drove straight and true thru the 2x4's and into the concrete block. I love using my P&C brad/finish nailers, but I need to drag around the compressor. With the Paslode, I just grab the case (very light weight) and go. Saves time, saves money. Can't get much better than that.



3. Let the Buyer Beware: It is not obvious until you receive your Paslode nailer that it is not to be used above 4500 ft (according to technical support) and the box says 5000 ft. We live in Colorado at 7500 feet and of course the gun is Dead ON Arrival - no fault to the gun. And then you can't return it for a refund because it runs on gas ... so let's just say that this was a VERY disappointing purchase from Amazon, who should be able to state very clearly the limitations of every product sold.
   
   My Bad - but a nice gift for someone near sea level....



4. I bought this framing nailer for a small (12x16) cabin we were building in the Adirondaks. Since we had to haul everything up to the site the lack of need for compressor and airhoses was attractive. I am a good rough carpenter but not a professional. I had never used a power nailer before.
   
   We used the framing nailer for about 5000 nails over a two-week period and had only one jam, easily cleared. It was extremely reliable and had sufficient power for all our purposes. Some of the complaints about the speed of nailing were not an issue for us since we aren't a high-speed operation. There was no point at which the rapidity of firing was a problem for us. Toe-nailing was a bit of an issue but it was mainly a matter of getting used to aiming the thing to put the nail where you want it to go. Once I had the hang of it I really liked toenailing with the framing hammer.
   
   I liked the fact that the wood would not move when nailing or toenailing. The Paslode nails worked flawlessly, didn't try any other brand. I had no problem with the depth of the nails. Any need to change the depth was easily adjusted. No problem with misfiring. The belt hook and rafter hook was extremely useful. Great feature. Liked the safety of the fact that it would not fire until the tip was depressed and then the trigger pulled in sequence. If you hold the trigger down and depress the tip it won't fire. We had no accidental firing. Cleaning after the two weeks took about ten minutes and the instructions were very explicit.
   
   I am very happy with this tool.



5. I'm getting a little long in the tooth for construction projects but I decided to build a new garage anyway. I struggled with which nailer to buy so I could avoid the tendon strains and sore muscles from using a hammer. Dragging a compressor around did not appeal to me. It was between the Hitachi and the Paslode. Too many bad reviews on the Hitachi. I bought the Paslode and have run a half box each of 3" and 2" nails through it. The depth adjustment is terrific and simple. You can drive as many nails as you want as quickly as you can press the gun into position to fire. I wish the magazine could hold more nails. Every framing gun that I have used was always a little heavier than you want and this one is no exception. I am glad I purchased the nailer and my garage walls are standing because of it. Can't wait for the trusses to arrive.

5 comments about Wilton 63302 6-Inch Shop Vise.

1. I broke two vises from Harbor Freight so I decided to try a Wilton. So far it has held up great.



2. WMH Tool will refuse to honor the lifetime warranty if your vise breaks, they will claim it's your fault, you'll be stuck with a broken vise...



3. Looking for a heavy vice for the studio and this one was IT, at 45# shipping weight it is a good heavy casting. Amazingly it came priority mail to the post office for FREE with the free shipping deal.
   Amazon had the best price and shipping deal, this is the vice to buy.



4. Called Wilton and was told the 63302 is made in China. Customer service stated that there is nothing comparable in this price range that is made in the good old United States. How sad! What will future generations think? Out source out source



5. Don't know why some one would give this vice a thumbs down. I may not pound on it like some folks might, but for my needs (a custom fishing plug builder) it far exceeds my expectations. I have no idea if I'll say the same thing after 60 years (the age of my previous vice) I will definitely not be using it in 2068...more than likey I'll be looking at the grass from the brown side :>) I give it a 4...because nothing man- made is perfect.

5 comments about DEWALT DW7353 Chip Collection Accessory for DW735 Planer.

1. Or perhaps I should say..Controls the Dust blows from the Dewalt Thickness Planner. If one makes sure the bag is tight it works well and you guys got it here quicker and more effeciently than ANYTHING else I've ordered from Delta/Porta Cable/Dewalt. Thanks for the attentive service



2. This product is really good if you don't have a powered dust collector. I have my shop in the garage and have so many tools, that I usually have to move things onto the driveway to work. I have tried using a shop vac with this planer, but it blows harder than the vac sucks. With this item, I simply hook it up to the machine, move a spare metal trash can close, and put the bag part over the can. It still produces dust, but nothing like with the shop vac.



3. Most useful accessory I have purchased for my shop in years. If you do not have a vacuum system in your shop, the Chip Collection Accessory is a must have.
   
   The chip blower on the DeWalt DW735 planer is powerful enough to direct the chip through the 10 foot plastic hose and into whatever receptacle you secure the fabric hood over. I use a 30 gal plastic garbage can. The draw string secures around the outside of the rim of the garbage can. 95% of the chips are collected directly in the garbage when you operate the planer.
   
   The only negative thing is that with the draw string attaching to the rim of the garbage can, there are some chips that will collect between the outside of the rim and the fabric hood. When you take the hood off, these chips will fall directly on the floor at the base of the garbage can but they are all around the garbage can and makes clean up easier.
   
   As the ground wire connects directly to the DW735 planer making removing the hood a bit more complicated, I crimped a spade type connector onto the end of the wire. When I want to remove the Chip Collector, I simply unplug the ground wire from the DW735 and release the locking collar ring from the planer discharge port.
   
   Good value product. I would definitely recommend this accessory.



4. The hood works well with a 30 gal trash can but a 55 gal drum would work better if your doing quite a bit of work. Putting a rope over a beam and raising the flex tube in a U shape help's also. I'm happy with the way it work's and on a scale of 1 to 10, I give it an 8 as there is some fine dust that come's through the cloth.



5. PROS:
   Having used several other planers, the DeWalt 735 is a real winner. I have 3 of these units. I placed the planers on a Rubbermaid carts & slid 30 gal trash cans below (bottom shelf). What a blessing - to plane & not have dust / chips flying everywhere. Thess planers are super & super easy to use (& change blades).
   CONS:
   The draw string doesn't grip sufficiently. But, adding a ratcheting strap clamp solves that problem.

5 comments about DEWALT DW716 15 Amp 12-Inch Double-Bevel Compound Miter Saw.

1. This saw is great. I'm still getting used to all the features as I am used to using a much simpler saw. I have build quite a few shelves so far and will be doing flooring soon. Great saw and the stock blade isn't half bad either. I find that aligning the cut with the blade is perfect and I won't be buying the laser attachment.



2. After purchasing and then returning a Hitachi 12" dual bevel saw that had quality issues purchased from Lowe's (I wrote a review for that saw), I decided to purchase the DeWalt DW716 from Lowes. I really liked the DW716. Easy set up and accurate. I'm in the middle of installing crown and larger baseboards in every room in my house. After making three cuts, this saw just quit. Nothing, nada. The owners manual troubleshooting section states nothing of an overload or reset on this saw. It says to check that the power cord is plugged in (check) and check that the C.B. or fuse is not tripped (check). The 20 Amp circuit was fine (120 Volts measured). I went ahead and ate lunch, came back still nothing. Probably a bad switch or loose connection. I took the saw back and ordered a Bosch 4212L. Fast shipment from Amazon. I immediately fell in love with the Bosch saw. Short lived love affair, I discovered this saw was broken at the locking pin that holds the saw head assembly right out of the box. The pot metal had chipped in the area where the pin extends and the pin would keep slipping allowing the saw handle to move up. After talking to a Bosch factory rep. he said this is a total disassembly of the saw. This saw was probably a returned saw. One of the bags containing parts had been stapled back together. All other bags were like they were factory sealed. I am currently in the process of returning the Bosch saw back to Amazon.com for a refund. So far Amazon's return process has been excellent. Tomorrow, I will go back to Lowe's and purchase a second Dewalt DW716. I would try another Bosch from Amazon but I don't have the time to sit around and wait. The same thing could happen. I did like the features of that first DW716 and I figure it could have just been one of those things. That DeWalt has straight forward adjustments for the blade tuning. It's probably just my current situation, but I have run into many quality issues across the spectrum from many brands recently. I'm getting paranoid. I now know that Hitachi is having quality issues for sure (Made in China). The Bosch was (Made in Taiwan) the DeWalt at least is North America (Made in Mexico). Maybe we need to get some of this work back. Sorry, I'm venting.



3. Even though I was just using this to put a floor in my sunroom (and don't have much skill with power tools or carpentry), I thought the saw was easy to use, safe, and accurate. I found it worthwhile to buy a good quality saw, as it appears the Dewalt will continue to perform for many years to come.



4. Nice saw - so far so good, I hope it last as long as my single bevel chop saw...



5. I got this saw for about $370 (free ship) +free palm sander....great deal and both tools are great. For the novice user, you can save $ by buying a "non-compound" saw since crown molding can be cut in a vertical position without compound cut. Wish someone told me, could have saved more, but it's awesome if you need the feature.

5 comments about Bench Dog 40-031 ProMax Cast Iron Router Table Extension for a Table Saw includes fence and Insert Plate.

1. What a refreshing change to purchase an American-made product and find that it is well-designed, well-made, well-packaged, all the parts are there, they all fit together, and the assembly instructions actually relate to what's in the box.
   
   A few minor quibbles, though: There was no hole in the table edge for mounting the Unisaw power switch, even though I'm sure many of these tables go on Unisaws. The tables did not end up perfectly flush, although I'm not sure if there's a hump in the Bench Dog table or a dip in the Unisaw's. The dust port is very loose, I'm going to have to come up with a way to tie it down. Screws to mount the router to the insert plate were not included even though the manual says they are. The manual also advises that there may be extra hardware in the package, but I ended up with 35 assorted bolts, screws, nuts, washers, and spacers, enough to make me seriously question whether I had done something wrong.
   
   All the above notwithstanding, this is a terrific product, five stars all the way.



2. I agonized for months over the price, and finally did it. All the way.
   
   I've added mine to a Delta Left-Tilt 10" contractor 36-982. There were a few minor problems on the install (nice tip on the extension roller). I pulled the left extension plate from my saw, replaced it with the Benchdog plate, and was then able to bolt the spare Delta left plate directly to the right side of the existing right extension plate. All of this takes up no additional space in my very small shop. That all took about a hour, fiddling with the roller, moving the saw, working the bolts, leveling, etc., mostly due to the weight, plus a small fudge factor for operator ineptitude.
   
   Next I started to assemble the other parts including the miter gauge guide track. In screwing the track to the plate, I found that either the counter-sink holes for the screw heads had not been drilled deep enough, or they shipped screws with heads too high. In any case about 1/16 - 1/8 of an inch extended up into the track making it impossible to move the miter gauge bar in the track. I called BD and they attempted to talk me into drilling the countersinks deeper, but for $329, I expect them to ship properly machined components. I'll report back on how long it takes them to ship the replacement, and if it's any good. Worst case, I have a drill press and the correct sized drill so I can fix it if necessary, but if I have to jury-rig an expensive tool to make it work properly I won't be happy.
   
   6/11 report back - BD shipped a properly machined replacement track (counter-sinks on original were not deep enough) immediately, and I had it in-hand inside a week. It now all works just peachy. I'm using my Biesemeyer rip fence, and my Delta and Kreg miter gauges. Nice. I came away with the impression that BD maybe has five employees; but they seem to know machine tool work when they set their minds to it. The customer service call went through Rockler, by the way. They took the call at the 800 number and sent an email to BD about the problem. The email was the only description that came with the new part.
   
   The additional plate on the right causes no instability, so I haven't added the support legs. I had not installed the Delta right side wooden extension table, so now I have spare parts. With the saw now weighing in at over 300 pounds I don't see much vibration. The length of my table is now nearly 60 inches, and all of this took up not one inch more space in my shop.
   
   A truing block I use to check my saw table can identify no problems with the Benchdog table anywhere, and it looks like they may have read some of the posts here because the sharp edges on my table were already rounded.
   
   The phenolic plate is solid but not exceptional. Okay for something like a PC 690 router, but not something heavier.
   
   I followed this purchase up with the Pro-Lift/PC 7518 router combo. It's evident that somebody talked to somebody, because the only evidence I see that the saw, the table, the lift and the router weren't all intended to always be assembled together is the BD table is a different shade of grey, and even that's changing as it gets waxed, etc. Seriously, the left-side Delta extension moves to the far right side with no modification; Delta even left pre-drilled and threaded holes to accommodate that change. I had to add some new lock washers, but that was it. The weight of the router and lift on the left just about perfectly balances the extra plate on the right. Vibration is trivial for either the saw or the router.
   
   The fully depressed router doesn't even come close to interfering with the angle adjustment wheel for the saw blade. The router fence barely comes close to touching the router when hanging under the table. When extended the router collet extends well above the top of the table for changing bits. The only inconvenience is having to reach under the table and around the router to change the speed.
   
   I have to use space as efficiently as I can, and I can't imagine a more effective way to add a router table.



3. Exceptionally well made, clear instructions as to how to install. Configured for most table saws with a 4 or 3 hole install on a 27" table edge.
   
   I can't imagine putting this on a contractor or lightweight hobbyist saw without extension legs to support the heavy cast iron base - to be fair the instructions recommend support legs in that situation.
   
   Mine fitted my Grizzly Hybrid G4078 just fine and the very flat table supported by the mass of the saw gives an excelent router table in my limited space garage shop.
   
   The insert plate comes with most "standard" router holes pre-drilled - an excellent full scale template gives drilling centers for most other routers on the market if you have one not covered by the supplied plate. The fence is solid for it's dimension. Includes fence inserts to allow use as a small scale joiner for preparing boards for edge glueing. Dust port works amazingly well for its simplicity.
   
   Highly recommended.



4. This is obviously not a review, rather a question. Does anyone know if this compatible with a left tilt saw? I have emailed Bench Dog for the last 6 months but no response.



5. I bought this when I replaced my 35 year old table saw with a Jet JPS10 Hybrid (both from Amazon). The installation was very easy, 3 bolts on the side of the table. I called ProMax to check if any other support was required. They assured me that the 3 bolt installation was all that was required.
   I've been using it for about 6 months. One of the best tools I own.
   1. It saves the space required for a separate router table.
   2. It's incredibly handy, right next to the table saw. I now use the router table twice as much as before.
   3. It's built like a brick outhouse. The aluminum fence is very easy to use and accurate.
   
   I highly recommend it for any serious woodworker with a small shop.

5 comments about Bosch 1199VSRK 8.5 Amp 1/2-Inch Hammer Drill.

1. I've found this tool to be a dependable workhorse in the class of work it was designed for. I've used it on jobs that involved hundreds of concrete drill holes, typically 1/4". I've had it in use for 90 days and it's a keeper.
   
   I bought it because Bosch makes excellent rotary and demo hammers. It's the only Bosch tool I own. My equipment includes Milwaukee, Dewalt, Makita, etc.
   
   12/29/07 My experience with the 1199 continues to be 100% positive. We put this type of tool to heavy duty use, drilling concrete and block. The tool sometimes undergoes multiple hours of run time in a single day. The 8.5 amp motor stays cool under work load and has never exhibited any indication of significant strain. Letting the tool do the work is critical.
   
   Sizing the tool to the job and using it correctly are essential when working in a business environment. My reason for selecting this hammer drill was the power weight balance. It's a two hand drill that comes in at 6 lbs. and offers high and low torque capability. Any frequent work above ½" in concrete essentially requires a rotary hammer which is typically a heavier tool.
   
   Previous reviews noted issues with "wobbling" chuck(s) and electrical failures. Electrical problems typically become evident quickly and I'm confident Bosch's unconditional warranty holds merit. The chuck issue can quickly be addressed as the drill comes out of the box, brand new. If it runs true with a bit attached at max speed, no load, then the chuck is fine. The hammer action of this drill is serious business and should not be construed as a chuck fault.
   
   I'm not particularly brand loyal across the board. I believe most contractor grade tool manufacturers have particular products that prove themselves superior on the job. I've since added another Bosch tool to my equipment, based primarily on it's reputation and my experience with this tool.



2. I bought this upgrade after I burned my Ryobi up. The job that killed the Ryobi consisted of twelve 9/16" holes into 1/2" thick steel and twelve 1/2" holes into concrete at a depth of 2 3/4", however, I was seeing blue sparks even before this job. After very slow progress on the first 9 steel holes and first two concrete holes the Ryobi quit. It had had seen some medium and light duty before that. It really struggled cutting through ceiling and floor joists with self propelled auger bits.
   
   I brought in the Bosch to finish the job and it was strong and smooth. What a time saver too! It was surprisingly powerful on the high speed setting. It cut the steel and concrete both like butter one either the high speed or high torque settings. I took it around back after the job and tried some self propelled auger bits that the Ryobi had struggled with. The Bosch chomped right through the 3+ inches width of a pressure treated 2X4 without a problem on both high and low speed settings with 1" and 3/4" auger bits. There is no wobble in the chuck. It's a fine machine and it compares well to Milwaukees I have used in the past. It has also seen the worst I can give it.
   
   Some finer details about the drill:
   - It will take some getting used to pulling the key from the detachable holder and putting it back. I'm used to just grabbing the cord where the key is and going to work.
   - Read the case and make sure you have it upright before opening it.
   - The case is nice. Although it seems compact it has room for a box of bits and plenty of loose ones.
   - Extra long cord is nice too.
   - Depth gauge is reliable and sturdy (better than others I have seen.)
   
   Update 1/08: I've used the drill for a few more jobs including some electrical work and some concrete with Tapcons. She is still running strong and smooth, and it's really a pleasure to use. I forgot to mention that it comes with an anti-kickback feature. Someone was helping with the Tapcons, and I saw them twist the bit pretty badly. The chuck stopped cold without even so much as a jerk. That's a nice safety feature to have on a beast like this.



3. I just wanted to echo one of the earlier positive reviews and say that the integrated slip clutch is a great feature. It is not uncommon for bits to catch in masonry and when this happens you have a few possible results: a broken bit (stuck in the hole?), a bit that is spinning in the chuck, or a drill that spins into you. This slip clutch in this drill goes a long way to preventing all of that. I'm now a big fan of this feature and, regardless of brand, wouldn't buy a hammer drill without it.



4. I bought this drill to install a gate in a sidewalk. It drove (8) 3/8" wedge anchors 2" into my sidewalk with no trouble in well under an hour. It was "reconditioned" so I was a little concerned but it perfomed like a marvel for the price. I am not a pro but I expect this drill would handle this type of job every day for some time.



5. I was drilling 3/4" dia holes 2 inches deep in concrete to install a pool cover when the drill just died. First thought my extension cord was unplugged.
   I have 14 of the 22 hoes complete and had to shut down.
   I had drilled about ten 3/8" dia by 3" deep holes about two months ago.
   
   In addition, the chuck kept loosening on me.
   
   My first Bosch tool and my last.

3 comments about Porter Cable 4216 Super Jig - Dovetail jig (4215 With Mini Template Kit).

1. I have a Jointech cabinet makers system to do dovetails, box joints, etc. etc. Learning to use that system was a real headache. It does a fine job and the joints look great, but because of the difficult process of making a through dovetail I thought I would get a jig to help me out. I would use the jig for the through dovetails and the Jointech for everything else.
   
   My first attempt with the 4216 met with great results. A few minor adjustments and it was turning out joints which looked nearly as good and were just as tight as a system I had spent well over a thousand dollars on.
   
   What is the trade off? Well, the 4216 is limited on the types of joints and sizes you can make. You can do 1/2 and 1/4 inch box and dovetails, both through and blind types. You can also do rabbeted blind joints. With a little imagination you can do variably spaced dovetails ... and they look pretty good. Last but not least, you can make sliding dovetail joints.
   
   The joints ARE fairly basic ... they don't have the "handcrafted" look of the expensive system. You can see the rounded sockets on the inside of the blind dovetails. The sizes of the joints are pretty limited ... only 1/2 and 1/4 inch. But if you want a quick dovetail/box joint with a less expensive piece you are buiding with almost zero hassles, this is the jig to get.
   
   For less than $200 you can begin to make these joints. The setup is easy. There are even depth guages on the jig to help you set the depth of your router bit. Instruction are clear and detailed. The jig is very well built and will last a lifetime. I find myself using it more and more ... even for the blind joints. I've developed a few tricks to improve the looks of the joints ... by rabbeting the inside of the side piece a tiny bit to hide the round end of the socket. Really, for the price you cannot get a better made, better working or easier to use system.



2. It takes a little getting used to ,but after a few mistakes I had much success. It was just a matter of reading the directions.



3. I loved woodworking in High School & after 35 years decided to have my own shop & get back into woodworking ( one of those mid-life things).I bought this & a Porter 890 router. Both awesome tools.The instructions are easy to use. Most everything you need to know is on the machine.
   My first open dovetail joint actually fit very well. The mini dovetail template is a gotta have ,so go ahead & spend a little extra to get this & not the 4212 jig. Small jewelry boxes with open dovetail joints are very classy. With is set up you can turn out great joints in no time!

4 comments about Skil 180BAT 18-Volt NiCad Pod Style Battery Pack.

1. the batteries and the2867 drills are good working tools i own 2 of these drills and 4 of the skil 180bat 18v . But the chargers are not good at all. my 2 chargers only lasted 6 months. i exspect more than that from a $50.00 toolw/batteries costing over $40.00 each. i have been serching for a new charger for 2months now with no luck. the drills have good tourque and the batteries last a good length between charges. but the problem with chargers and access to buy replacements makes this almost a useless tool



2. I would use this for light to medium duty jobs. It is great for driving screws or boring holes in wood, etc. anything that a cordless drill can do. I tried using it with my 18V drill to mix mortar however and it had trouble. Otherwise it performs according to how you would expect.



3. Original battery became shorted, not knowing this I ordered several chargers each of were were corupted by the battery. So with technical support from Skil I was able to determine that the battery was at fault not the chargers. New charger and new battery and I was back in bussiness.



4. The battery I got from Amazon (Skil B180) is perfect! And the price was the best I could find anywhere.
   
   Don Z.

5 comments about RotoZip DC1 Duracut Bit Pack.

1. I am a remodeler and cutting plaster/buttonboard in older houses can be tough. I got only one hole cut for a six 6" can lights before my Greenlee hole saw was ruined. This bit in my Rotozip cut the last five and plenty of holes in the walls for outlets and for pulling wire (unlike a regular electrician I have to patch my holes so a square cut is worth it) . It did take a couple bits (you can see the "teeth" getting worn down) and near the end of a bit's life, you get more cutting by working the bit in and out. It's a dusty job and you should wear more than a cheap dust mask. I also found a full face shield worked much better than goggles.
   I have been trying to buy some more of these bits at Home Depot (couldn't wait for a Amazon order) but the clerk told me that Bosch had just bought out Rotozip and that it would be a while before new bits came in under the Bosch name(?)
   $10/bit is expensive but they get the job done.



2. I have a 1940's home and bought this bit to cut the top of my living room wall's perimeter, just below the curve at the coved cieling because the walls are shot and need to be redone. My walls consist of 1/2 inch drywall with 1/4 + inch mortar, and 1/16 plaster and about 10 coats of paint. It's a DUSTY job, but the bit did it without a problem. I was just praying not to hit one of the drywall nails. For the home user, the tool is great and serves its purpose.



3. RotoZip DC1 Duracut Bit
   
   Pros:
   
   - 1/4" bits have significantly greater resistance to breaking than 1/8" bits. It's still possible to snap one, but you have to use much more force. If you are frustrated with how easy it is to snap 1/8" bits, and your application will be OK with a 1/4" bit, try one of these. (Of course, the tool will need a 1/4" collet.)
   
   - Carbide cutters last much longer than tool steel.
   
   - Works quite well on soft materials, such as most wood, plastics, and drywall. Has an excellent life if used only on softer materials. They work best at very high speed. I.e., instead of a drill, try them in a router or high-speed rotary cutter.
   
   Cons:
   
   - As with any such bit, when the material gets harder, it becomes less effective -- to useless. E.g., using it on hard products will dull the bit in a hurry. E.g., porcelain or other hard tiles, concrete products such as blocks, bricks, concrete stucco (in spite of their sales pitch), glass, steel, etc. They work pretty well on some tile backer-boards, but this wears them out faster.
   
   Other:
   
   Cutting some materials, such as drywall, creates lots of dust. I use a respirator.



4. I bought this bit at home depot for $8 and used it to cut 4 sheets of hardebacker board into a circle for an outdoor mosaic table substrate, using a 3 1/4 hp router and trammel arm. The bit worked quite well, athough I noticed I had to get the RPMs up on the variable speed router to get it to cut easily. I doubt using this bit in a lower powered roto zip could've produced the same results.
   Perhaps the folks who don't like this bit should retry it in a router.



5. I used this to route a trough up my wall to conceal speak wire to my home theater speakers. It worked like a charm!!! My house is 1955 with plaster/mortar walls. I also used the dust extractor adapter - What a charm ABSOLUTELY NO DUST!!! If you have a Rotozip and a dust problem you need the dust extractor!!!

4 comments about Makita 192638-6 9120 9.6-Volt 1.3 Amp Hour NiCad Pod Style Battery.

1. Have used the product for 3 weeks and works fine. It was cheaper than most retail stores and it came to my house with free shipping.
   Thanks, RW



2. My Ace Hardware, the local distributor of the Mikita line, doesn't carry (and wouldn't special order for me) this 9.6 volt battery. I'm thinking they wanted me to upgrade to the next and newest. But I really like my currant driver/drill, it's the perfect size for me and it still works great. Now that I've found the battery for it I'm set!



3. Just what I needed to get the drill going again, at a price that was acceptable.



4. My husband was very happy and satisfied (I would say delighted) with this product and Amazon, and he doesn't usually like to order by internet or catalog!