No comments about 3M 81431 4-Inch x 24-Inch Purple Regalite Resin Bond 80 Grit Cloth Sanding Belt - 5 Pack.

1 comments about Milwaukee 48-28-4001 5-1/2-Inch Hex Shank Extensions for Selfeed Bits, Auger Bits and Hole Saws Over 1.

1. You cant go wrong when you buy Milwaukee, and this product does not disappoint. It is a classic design that has been used for years, and it works well with all the Hex Shank Self Feed Bit components.

5 comments about Delta 50-445 4-Inch Dust Collector Chute (For Models TP400LS, 22-565 and 22-560).

1. The thing works spectacularly, I couldn't believe how little shavings there were on my work table because of the dust collector. I was shocked because the planer was attached to about 10' of 4" hose on a 1 hp dust collector, so my expectations were pretty modest. Instead of having to sweep up half a trash can of shavings they were all in my dust collector! There were a few shavings that kicked back on the infeed side of the planer but that was all!
   
   My only complaint was the directions, or lack there of! There was nothing in my box other than the dust collector chute and two knobs, absolutely no directions. I went to the web-site and that was fruitless. I tried several options to install the dust chute and nothing seemed to make sense. Until I removed the plate over the cutter blades and realized that the dust chute replaces that cover and allows for dust collection. It took seconds to install once I made this discovery. The point is they could have had a simple one page direction and possibly the red letter warning lable about the cutter blades that is on the factory plate. But then I would have had to rate the tool as a 6 on the five point scale! If you own a dust collector and a 22-560 planer this accessory is a must!



2. I can't really rate this because I had to send it back since it did not fit my planer. When looking at my planer on amazon, this chute is listed as an accessory, but when I received it did NOT fit. You must get the 50-359 for the TP-305 planer.



3. Nice design, easy to install (though no instructions included, but common sense is required). Once installed the planer was slightly quieter (when used with a dust collector). Good deal for the money.



4. What a great addition to any shop. I put a reducer on it and use it with my shopvac. I couldn't be more pleased. As far as it coming with no installation instructions if you are mechanical enough to plan wood You are mechanical enough to install this without instructions.



5. This was a snap install. Plaining wider boards nothing excapes, when plaining narrow wood a small amount of chips may excape. Overall this has helped my shop stay far cleaner

No comments about Multi-Code 4200-01 Garage Door Opener Keyless Entry.

1 comments about DEWALT DWD110K 7.0 Amp 3/8-inch VSR Pistol Grip Drill Kit with Keyless Chuck.

1. This drill provides very poor performance in the lower speed ranges, such as when drilling metal, esepecially with larger bits. The speed control is very poor, and the torque/power is also poor. I've never seen a drill that I could stall a low/moderate speeds as easily as this one.
   
   It seems to be OK at higher speeds, so if you only use small bits and drill in soft material like wood, you might find this drill acceptable. But I bought it for use in a variety of materials, including metal, and it has been a disappointment.

5 comments about DEWALT D180002 Standard Electricians Bi-Metal Hole Saw Kit.

1. I own this set, along with many other DeWalt hole saws and have found them to be excellent tools. I primarily cut hard woods, but have also used them on 16 guage stainles with great results.I would recomend these to any one



2. I got a gift certificate from work...100 bucks
   
   I sometimes have a need to drill holes at work...sometimes holes as big as 2 inch to run conduit and tubing thru. I have a work provided set of hole saws but wanted my own....I do have numerous hole saws around the house from working over the years but wanted a set in its own case.
   
   Have not used the set yet and may not use for a long time but like most name brand tools I am sure the quality is fine...and the case is really nice for a set of hole saws. I have a starret set at work and the little plastic case clasp is broken...you wont have to worry about the clasps on this dewalt case breaking as they are nice....like the ones on their power tool cases... It also has a handle which is nice.
   
   IF I ever wear out the saws I can replace them and still have a nice cased set....
   
   If you need a hole saw set and the sizes you need are in this set then get it because it is a quality set.
   
   I bought from tool king and was very satisfied with their service...fast shipping.



3. Love the case best, wish I had a complete set of the large ones in a handy case like this. Good Dewalt quality tools. Very easy to handle.



4. Sturdy and sharp bits. I have yet to be disappointed with a DeWalt product.



5. Comes with 2 quick release chucks. Made with high quality steel. These will outlast those cheaper hole saws and will cut through anything. Good variety of sizes.

2 comments about 3M 81399 3-Inch x 21-Inch Purple Regalite Resin Bond 50 Grit Cloth Sanding Belt - 5 Pack.

1. This sandpaper will give users many more hours of use than typical paper. I managed to sand my entire deck with a few belts. Highly recommended...



2. These belts are of higher quality than the off-the-shelf belts at the chain hardware store and last longer.

No comments about Stabila 37924 - 24-Inch Electronic TECH Level.

3 comments about Kreg KMS7303 30-Inch Jig and Fixture Bar.

1. It's very long, and very nice. The plastic allen screws do not scratch the miter slots.



2. I purchased the Kreg Jig & Fixture bar to build a panel cutting jig for my Rockwell table saw. The Kreg bar comes with a series of threaded holes along the bar into which nylon set screws can be inserted. This feature allows a snug fit in all miter slots. The bar has counter-sunk holes for attaching to your own plywood, and the screws are included. For the money I could not find another product with the length and features of the Kreg bar.
   
   Attaching the bar to the plywood base proved to be trickier than I had imagined. Perhaps it was my own inexperience, but I found it near impossible to prevent some deflection of the bar when it was attached with the provided screws. Because the holes in the bar are counter-sunk, any minute deviation in the screw placement will pull the bar one way or another, resulting in the bar being less-than-perfectly straight. I assumed the set screws could be used to "correct" the error in the bar's position, but this was not the case. The result is that the jig slides smoothly for most of its travel, but binds in other places. Be sure that you insert the set-screws so that the end WITHOUT the hex-key slot contacts the saw's miter slot or you will destroy the hex-key hole and render the screw useless.
   
   I think someone with better skills and more patience could probably get better results. I would still recommend this product for anyone looking to expand their saw's capabilities.



3. The amazon purchase was perfect and I received the bars within a few days. The miter bar is machined with precision and the included plastic lug nuts allows the perfect fitting of the bar into the miter slot. This will perform much better than my home made wooden miter bars.

5 comments about MLCS Router Speed Control Heavy Duty.

1. I'm sorry that the router diddn't work out for me. MLCS was awesome in the return department,thank you so much!



2. In wood workshop you need better speed controller than those incorporated in drills angle grinders and many routers. However, they usually control speed without any load and at increased load they allow a significant drop of set rpm. The MLCS Router Speed Controller however keeps the set rpm nearly constant at any load. This is a great property which makes your work easier and more precise. You can easily use your angle grinder as an polisher. Your drilling is safer with optimum cutting speed. Any router runs without significant dropm in speed. The only additional care is needed due to the fact tha cooling at lower rmp decreases sharply. You have to make stops to allow cooling. and for me especially I cam use it for 240 V input.MLCS Router Speed Control Heavy Duty



3. This item is everything I had hoped it would be. Also the price was the lowest I could find.



4. Easy to order. Product was delivered quickly. Was bought to control a Makita 3612br and works great.



5. I bought the plastic case version of this same controller direct from MLCS. They indicated the workings are exactly the same as the metal case. When I got the unit, the instructions stated "not for use on capacitor start induction motors a.k.a. brushless motors." I spoke with an electrician friend, and he stated I would burn the motor out if it is a capacitor start. Planned to use it on my mini lathe, drill press, disc sander. They are all capacitor start. The price from MLCS for the plastic unit as an internet special was $20. A great price if I could have used it. The same unit through Rockler is considerably higher.