2 comments about Bessey SQ-12 12-Inch Super Quick All Steel Sliding Arm Clamp.

1. we own a metal fabrication, welding, and machine shop. we use these tools everyday. they are quick and easy to use. the strength of the besey clamp is second to none. we will purchase these clamps again in the future. A+++ or 5 star. thank you



2. I find this a great size and don't think the smaller clamps are necessary. I used it immediately to patch an auger on my feed grinder that I couldn't get anything else into position and squeeze the metal together to weld. It is much quicker to get on than a C clamp and you don't have to spend five minutes screwing it in or out. I farm and this clamp is big enough to clamp around auger tubes and equipment frames. I'll probably get another one.

1 comments about Surebonder 5910 Cordless Stapler.

1. After fooling with this stapler i found out how well it really does work, an i might add it does do a very good job, an the battery pack has some power behind it as well, for a hobbyist this is what you wanna get... had a bad impression at first but it turned out to be the stapler i like.. possible women could have trouble pulling the trigger but it may loosen up after a couple boxes of staples has gone through it... again folks i do like this product.. i used the 1/2 inch stainless steel staples they recommend..

No comments about Fiskars 70296935 21" Bow Saw.

No comments about Stanley 77-193 MW20 4-Inch Dual Wheel Measuring Wheel in Feet/Inches.

3 comments about Bahco Heavy Duty 2-1/2-Inch Replacement Scraper Blade #451.

1. After scraping many old houses and pieces of old furniture, I have found that Sandvik paint scrapers with their tungsten carbide blades are simply the best. Buy (use) no other. Surface preparation is critical to good paint adhesion, so invest in the best scrapers and blades on the market. I suggest buying all three size scrapers--the smaller ones not only allow you to get into smaller spaces, they also exert more pressure per square inch than the big one and are not as likely to be compromised by concave surfaces. They often remove what the bigger one leaves behind; they all remove what other scrapers leave behind--lots. Don't underestimate the value of your time--buy the Sandvik scrapers and blades. You will not regret it.



2. The Sandvik 450 is the best, easiest to use scaper on the market, with a carbide blade that seems to last forever. And when it does wear our, this little blade makes it like new for a few bucks. Simple.



3. This was an excellent purchase! This replacement blade is well worth the money, it removes paint better than any other and helps prepare your surface for a new coat of paint. Using other scrapers is a waste of time; nowhere near as efficient as this product. Get this blade. Highly recommended!

5 comments about Bosch 2607001312 Leg Extension for Digital Protractor/Angle Finder.

1. At first when I ordered this, I thought it was for longer pieces of work. It is actually for shorter pieces. This is an add on for the Bosch Digital Protractor. What this extension allows you to do is extend it just a little bit, or as much as you need, not off the end of the leg, but rather BACK OVER THE ELBOW OF THE UNIT, to measure the angle of something that may be only 3 or 4 inches in length. By extending it the short distance, getting the angle, then deducting it from 180 degrees you can get an accurate measurement. The instructions that come with it, show you a picture of someone who is outside,holding the protractor against a wall, and extending the extension backwards across the knee to get the slope measurement of an outside window sill plate.
   Anyhow, it is an infrequently used item for your Bosch Digital Protractor, but it does come in handy for the shorter pieces, and for the price it is a worthwhile addition. Hope this was helpful.



2. my best friend for crown moulding, takes a little work for a math idiot like me to convert the angle degree's over to the corresponding miter saw settings (dewalt) but now I see some of the miter saws coming out with degree settings marked out, so it wouldn't evan take work if you own one of them.

   The tool is flaweless and it has a multitude of uses, not only crown moulding, but base casing everything where angle has to be figured out.

   I got the case seperately a worthwhile expense, I aslo use it to tune up my table saw and miter saw. My only wish is that they would come out with a smaller version.




3. I bought this think it would extend the length by 18". NO, it just extends over the knuckle by 4". not really useful. Don't buy this if you think it;s going to give your long side legs. It doesn't



4. If you want to get the angle from the outside of a bent piece of tube >, you must have this. You open the device and slide the leg extender over the open end of the top channel giving you a surface to work with.



5. Well made but it will become just another dust collector. There are other manual angle finders on the market that are quicker and easier to use. The lack of a memory really makes this a time waster.

No comments about 3/8" Drive x 12" Mechanic Flex Breaker Bar.

No comments about KD Tools 3702 2 Piece Hog Ring Plier Set.

No comments about Oshlun MTEC-08 8-Inch Stainless Steel Digital Caliper with Super Large Display.

1 comments about IRWIN Marples Chisel Set M444/S4N 1/4", 1/2", 3/4", 1" 4 Pc. Set.

1. They're inexpensive, but don't keep a good edge for very long. You can get them pretty sharp, but the edge will be gone with a few mallet blows.